Product details
MDX91A-3800-503-4-T00: High-Power Multi-Axis Inverter for Demanding Cabinets
- Brand: SEW-EURODRIVE
- Model: MDX91A-3800-503-4-T00
- Series: MOVIDRIVE modular Multi-Axis Inverter (MDX91A)
- This book-style inverter drives multi-axis systems from a direct 3-phase AC line.
- It delivers 380.0 A rated output at 4 kHz PWM.
- Frame size 8 supports 4-quadrant operation and regenerative braking.
- An integrated DC 24 V auxiliary supply delivers 80 W. You can add external power if needed.
- Control modes cover U/f, VFCplus, CFC and ELSM synchronous motor control.
- A built-in brake chopper works with optional BR braking resistors.
- M10 copper busbars handle line and motor connections.
- The unit suits cabinet builders who need high current in a compact book format.
Technical Data
- Brand: SEW-EURODRIVE
- Model: MDX91A-3800-503-4-T00
- Series: MOVIDRIVE MDX91A
- Product type: Multi-axis application inverter, frame size 8
- Supply voltage: 3 x AC 380 to 500 V nominal, 50 to 60 Hz
- Line frequency tolerance: 50 to 60 Hz, plus or minus 5 percent
- Nominal line current: 342.0 A
- Rated output current: 380.0 A at 4 kHz PWM
- Recommended motor power: 200 kW for ASM motors
- Overload capacity: 150 percent of rated current at 2.5 kHz PWM
- Continuous current at 0 Hz: 350 A, which is 90 percent of rated current
- PWM frequency: 2.5, 4 and 8 kHz
- Max output frequency: 599 Hz in U/f mode
- Max output frequency: 250 Hz in VFCplus mode
- Max output frequency: 500 Hz in CFC and ELSM modes
- Nominal DC link voltage: DC 560 V
- Minimum braking resistance: 2.3 ohm
- Brake chopper peak power: 200 percent of rated apparent power
- Control modes: U/f, VFCplus, CFC and ELSM
- Operating mode: 4-quadrant operation
- Auxiliary supply: integrated DC 24 V, 80 W, expandable
- EMC variant: basic interference suppression integrated
- Protection rating: IP10 standard, IP20 with plastic terminal covers
- Pollution class: 2 per IEC 60664-1, overvoltage category III
Operating Environment and Durability
- Operating temperature: 0 to +40 °C without derating
- Operating temperature: +40 to +60 °C with derating
- Storage temperature: -25 to +70 °C, class 1K2, non-condensing
- Transport temperature: -25 to +70 °C, class 2K3, non-condensing
- Relative humidity: non-condensing, class 3K3
- Installation altitude: up to 1000 m without restriction
- Installation altitude: 1000 to 3800 m with 1 percent current derating per 100 m
- The drive resists cabinet vibration and common industrial noise when installed to manual guidance.
- Basic EMC filtering limits interference in typical cabinet layouts.
Communication and Compatibility
- Built-in system bus: EtherCAT with CiA402 profile
- Fieldbus control: ready for MOVIDRIVE technology variants
- Option card /CFN21A: PROFINET IO
- Option card /DFE32B: EtherNet/IP
- Option card /DFI11B: PROFIBUS DPV1
- Option card /CES11A: multi-encoder interface
- Option card /CID21A: encoder interface
- Option card /CIO21A: I/O expansion
- Option card /CS..A: MOVISAFE safety card
- Option card /L: conformal-coated PCB
- The drive fits the MOVI-C platform and MOVIDRIVE system.
- It works with ASM and synchronous motors under the listed control modes.
Installation Guide
- Mount the book-style unit vertically in the control cabinet.
- Keep clearance for airflow above and below the frame.
- Connect line and motor cables to the M10 copper busbars.
- Tighten terminals to the torque values in the product manual.
- Wire the integrated DC 24 V supply or add an external source.
- Install a braking resistor above 2.3 ohm when you need braking energy.
- Use plastic covers to raise protection from IP10 to IP20.
- Follow section 2.7 dimension drawings for cabinet cutouts.
Commissioning and Maintenance
- Start with the built-in keypad or the MOVISUITE engineering tool.
- Select the control mode that matches your motor and load.
- Run the motor identification routine for CFC and ELSM modes.
- Check DC link voltage and fan operation at first start.
- Clean cooling paths at each service interval.
- Inspect busbar joints for tightness and heat marks.
- Replace fans before bearing noise becomes audible.
- Keep spare option cards on hand for fast swap-outs.
Certification and Packaging
- The product manual is active and verified as of 2026-06.
- The drive carries the SEW-EURODRIVE product line status for the MOVI-C platform.
- Confirm final certification marks on the unit label for your region.
- Package contents: one MDX91A-3800-503-4-T00 inverter
- Package contents: printed quick start guide
- Package contents: terminal covers as ordered
- Optional cards and braking resistors ship separately.
FAQ
- Can this inverter run four motors at once?
- Yes, the multi-axis design supports several axes from one line feed. Check total current against the 342 A line rating.
- What happens if my cabinet reaches 55 °C?
- The drive still runs, but you must derate output current. Plan airflow early to keep full power.
- Do I need an external 24 V supply?
- Usually no. The built-in 80 W supply covers control power. Add external power for heavy option loads.
- Which encoder card suits a resolver?
- Pick the /CES11A multi-encoder card. It covers common feedback types in one slot.
- How do I cut noise on a long motor cable?
- Use shielded cable and bond the shield at both ends. Basic EMC filtering is already inside the unit.
- Can I mount it at 2500 m altitude?
- Yes, with about 15 percent current derating. The manual gives 1 percent per 100 m above 1000 m.
- What is the first check when the drive trips on overcurrent?
- Look at motor cable length and shield bonding first. Then confirm the PWM setting matches the load.

















There are no reviews yet.