Product details
ATV320U40N4WS: Built for Tough Machine Control
ATV320U40N4WS from Schneider Electric is a robust drive for three-phase machines. It delivers 4 kW (5 HP) at 380…500 V. The IP65 housing blocks dust and water jets. So it fits washdown zones and dusty floors. A Vario disconnect switch saves wiring time. The category C2 EMC filter is built in. However, you must add an external brake resistor for dynamic braking. Therefore, plan that part early. This drive runs both induction and PM motors. In addition, built-in CANopen and Modbus ports cut setup work.
Technical Specifications
- Brand: Schneider Electric
- Model: ATV320U40N4WS
- Series: Altivar Machine ATV320
- Type: IP65 wall-mount three-phase drive with Vario disconnect switch
- Motor Power: 4 kW (5 HP) at 380…500 V
- Supply: 380…500 V three-phase, 50/60 Hz, -15%/+10%
- Input Current: 13.7 A at 380 V; 10.6 A at 500 V
- Output Current (In): 9.5 A at 4 kHz
- Transient Output: 14.3 A for 60 s (150% of In)
- Output Frequency: 0.1 to 599 Hz
- Switching Frequency: 2 to 16 kHz; factory 4 kHz (derate above 4 kHz)
- Overload Torque: 200% Tn over-torque; 170% Tn braking
- Brake Resistor: 36 Ω minimum, external
- Analog Inputs: 3 total — ±10 V differential, 0…10 V, 0-20 mA
- Digital Inputs: 6 total — 4 configurable, 1 PTC probe, 1 pulse (20 kHz)
- Outputs: 1 digital (100 mA), 1 analog (10-bit), 2 relay, 1 pulse (32 kHz)
- Safety: STO up to SIL3/PLe; SS1, SLS, SMS, GDL
- Ports: 1 RJ45 for CANopen and Modbus Serial line
- Expansion: 1 slot — EtherNet/IP, PROFIBUS DP V1, DeviceNet, EtherCAT, POWERLINK, PROFINET
- Apparent Power: 9.2 kVA at 500 V
- SCCR: 5 kA
- Power Loss: 111 W at In
- Motor Cable: 10 m shielded at 4 kHz (C2/C3)
- Operating Temperature: -10 to +50 °C no derating; up to 60 °C with derating
- Storage Temperature: -25…+70 °C
- Humidity: 5…95%, no condensation
- Altitude: 1000 m no derating; 1% per 100 m above
- Protection: IP65
- Size (H×W×D): 340 x 250 x 235 mm
- Weight: 8.200 kg (18.077 lb)
- Terminal Torque: 1.4 N·m (Frame 3)
- Wire Size: 2.5 to 6 mm² (Frame 3)
- Clearance: 100 mm around drive; mount vertical ±10°
Installation Guide
- Mount the drive vertical. Tilt no more than ±10°.
- Leave 100 mm free space on all sides. This keeps airflow strong.
- Use 2.5 to 6 mm² wires on Frame 3 terminals.
- Tighten each terminal to 1.4 N·m.
- Keep the shielded motor cable under 10 m for C2/C3.
- Add a 36 Ω or higher brake resistor if you need braking.
- Seal all cable glands. Otherwise, the IP65 rating drops.
Setup and Service
- Set switching frequency from 2 to 16 kHz. Factory value is 4 kHz.
- Derate power above 4 kHz.
- Derate current by 1% per 100 m above 1000 m altitude.
- Plug in the VW3A1111 or VW3A1101 display for quick setup. Then you can copy settings to other drives.
- Clean the IP65 case with a water jet. Never soak the drive.
- Keep the drive dry. Stop condensation before power-up.
Compatibility Notes
- Runs induction motors and PM motors without a sensor.
- Ships with CANopen and Modbus Serial line.
- Add a module for EtherNet/IP, PROFIBUS DP V1, DeviceNet, EtherCAT, POWERLINK, or PROFINET. Thus one drive fits many networks.
- Fits GV2 breaker brackets, DIN rail plates, UL Type 1 kits, and 90-degree adapters.
Certifications
- UL 508C, UL61800-5-1, CSA 22.2 N274
- EN/IEC 61800-3 (C2/C3), EN/IEC 61800-5-1
- IEC 61800-5-2 up to SIL3, IEC 61508 SIL3, IEC 13849-1 PLe
- IEC 60721-3-3 (3C3/3S2), RCM, EAC, KC
Package Contents
- ATV320U40N4WS drive
- Installation manual NVE41289
- Safety sheet
- Quick start guide
Best Fit: Equipment and Applications
- Packaging lines: conveyors, wrappers, and case packers
- Material handling: roller tables, hoists, and transfer units
- Food and beverage plants: washdown zones and wet floors
- Pumps and fans: variable flow control in dusty rooms
- Textile and wood machines: high dust and lint areas
FAQ
- Q: My 4 kW motor trips the drive at start. What should I check?
A: First check the motor nameplate current. Then compare it with the 9.5 A output rating. Also review the acceleration ramp. A ramp that is too short pulls high current. Finally, confirm the motor is wired for the correct voltage. - Q: Can I run this drive without a brake resistor?
A: Yes, for most pump and fan duties. You only need the resistor when stops must be fast. If you skip it, keep deceleration gentle. Otherwise the drive may trip on overvoltage. - Q: The IP65 seal failed after cleaning. Why?
A: Check the cable glands first. Loose glands let water in. Also inspect the cover gasket for cuts. Re-tighten glands after any cable change. Never aim a jet at the cover seam. - Q: How do I know if derating applies to my site?
A: Measure the room temperature near the drive. Check the altitude above sea level too. Above 50 °C or 1000 m, you must lower the load. Use the derating curves in manual NVE41289 before you size the motor. - Q: Can this drive share one network with older Modbus devices?
A: Yes. The built-in Modbus Serial line port talks to legacy devices. For Ethernet plants, add the EtherNet/IP module. This keeps one drive family across old and new lines.














There are no reviews yet.