Product details
FCST1200F High-Flow Rubber-Seal MFC by Fujikin
The FCST1200F is a high-flow mass flow controller from the FCST T1200 Series. It covers 51 to 200 SLM of N2 equivalent flow. A rubber seal (FKM) and PCTFE seat keep the design cost-effective. Accuracy is ±1% FS in the 15-35°C window. Repeatability is ±0.2% FS. Response time stays at or below 3 seconds. The FCST1200F handles non-corrosive high-flow gases such as N2, Ar, He, and Air. It fits CVD chamber purge, bulk gas distribution, and high-flow semiconductor gas lines. The bellows-sealed diaphragm valve comes in N/O or N/C form. Standard fittings include 3/8 UJR or F900. This unit gives you a practical high-flow option with proven accuracy.
Technical Data
- Brand: Fujikin
- Model: FCST1200F
- Series: FCST T1200 Series (FCS-T1200F High Flow, Rubber Seal)
- Module type: Mass flow controller (MFC)
- Full-scale flow range: 51 to 200 SLM (N2 equivalent)
- Control range (turndown): 2-100% FS
- Accuracy: ±1% FS (guaranteed from 15-35°C)
- Repeatability: ±0.2% FS
- Response time: ≤3 seconds
- Linearity: Covered by the ±1% FS accuracy spec
- Resolution and sensitivity: Set by the sensor and full-scale range
- Operating temperature: 5-45°C
- Gas type: Customer-specified process gas; high-flow non-corrosive gases (N2, Ar, He, Air, etc.)
- Operating pressure: Max 700 kPaG; required differential pressure 100-300 kPa
- Wetted materials: SUS316L stainless steel, PCTFE seats
- Seals: Rubber (FKM)
- Valve type: Bellows-sealed diaphragm valve (N/O or N/C)
- Leak integrity: ≤1×10⁻⁷ Pa·m³/s He (rubber seal)
- Electrical interface: Analog 0-5 VDC (±15 VDC); 4-20 mA (+24 VDC); digital RS-485, DeviceNet, EtherCAT
- Power supply: ±15 VDC (0-5 VDC analog); +24 VDC (4-20 mA)
- Heated option: No (standard unheated version)
- Fittings: 3/8 UJR or F900
- Compliance: RoHS compliant; CE
Installation Guide
- Mount the FCST1200F with the flow arrow matched to real gas direction.
- Keep inlet pressure at or below 700 kPaG.
- Provide 100-300 kPa differential pressure for full flow.
- Use 3/8 UJR or F900 fittings that match your gas panel.
- Wire the analog or digital interface that fits your tool.
- Keep ambient temperature between 5°C and 45°C.
Setup and Maintenance Convenience
- Fast response (≤3 s) shortens purge and switchover steps.
- The bellows-sealed diaphragm valve resists wear.
- Simple analog and digital options cut wiring time.
- FKM seals allow low-cost field service.
- The compact body fits tight gas panel spaces.
- Wide 2-100% FS control range covers many recipes.
Compatibility Notes
- Works with RS-485, DeviceNet, and EtherCAT fieldbus tools.
- Analog control supports 0-5 VDC and 4-20 mA systems.
- Suits N2, Ar, He, and Air lines in semiconductor fabs.
- Pairs with 3/8 UJR and F900 fitting standards.
- Fits CVD chamber purge and bulk gas distribution skids.
Certification and Compliance
- RoHS compliant.
- CE marked.
- Leak integrity at or below 1×10⁻⁷ Pa·m³/s He.
Packing List
- One FCST1200F mass flow controller
- One calibration and test report
- One user documentation set
- One fitting kit (3/8 UJR or F900, per order)
- Protective caps and shipping carton
FAQ
Q: What makes this model a good fit for high flow?
A: It covers 51-200 SLM with a wide 2-100% FS control range. The bellows diaphragm valve stays stable at high rates.
Q: Which gases can I run through it?
A: Use non-corrosive gases such as N2, Ar, He, or Air. Tell us your gas at order time for the right calibration.
Q: How much differential pressure does it need?
A: Plan for 100-300 kPa across the unit. Low DP may limit top-end flow.
Q: My flow drops at high set points. What should I check?
A: Check differential pressure first. Then check the inlet filter for particles.
Q: Does it need heat?
A: No. The standard unit is unheated and works from 5-45°C.
Q: Can I pick N/O or N/C valve action?
A: Yes. Both normally open and normally closed versions are offered.
Q: What fittings come standard?
A: Choose 3/8 UJR or F900 at order. Both fit common gas panels.
Q: Which digital protocols does it support?
A: RS-485, DeviceNet, and EtherCAT are supported alongside analog control.














There are no reviews yet.