Product details
FCST1050MZF-HT Heated MGMR MFC for Condensable Gases
- Brand: Fujikin
- Series: FCST T1000
- Family: FCS-T1000MZF-HT High Temperature MGMR
- Type: Heated multi-gas mass flow controller
- Built for
- Condensable gases
- High-vapor-pressure sources
- Halogen and corrosive gases
- Core strengths
- Heated flow path from 50°C to 80°C
- MGMR multi-gas and multi-range memory
- Hastelloy C sensor resists corrosion
- ±1% S.P. accuracy at 25–100% set point
- Flow range
- 30,001 to 50,000 SCCM (N2 equivalent)
- Bin 8 configuration
- Turndown from 2% to 100% FS
- Why it saves money
- One unit covers many gases
- Lower spare parts stock
- Fewer line changes
Technical Data
- Model: FCST1050MZF-HT
- Accuracy
- ±1% S.P. (25–100% of set point)
- ±0.25% FS (2–25%)
- Repeatability: ±0.2% FS
- Response time: ≤1 second
- Operating pressure
- Max 400 kPaG
- Argon: 500 kPaG
- Wetted parts
- SUS316L stainless steel
- Hastelloy C sensor
- PCTFE seats
- Seals: Metal (Au gasket)
- Heating
- Flow path heated to 50–80°C
- Custom calibration temperature on request
- Electrical interface
- Analog 0–5 VDC (±15 VDC supply)
- +24 VDC option (0–5 VDC / 4–20 mA)
- Digital RS-485
- Power supply
- ±15 VDC (0–5 VDC analog)
- +24 VDC option
- Valve: Bellows-sealed metal diaphragm (N/O or N/C)
- Leak integrity: ≤1×10⁻¹¹ Pa·m³/s He
- Dimensions: 125 (H) × 124 (W) × 70 (D) mm
- Compliance: RoHS, CE, EP surface finish
- Remote electronics: Available as an option
Best-Fit Equipment and Applications
- CVD tools
- Liquid precursor delivery
- Warm lines keep vapor stable
- Etch chambers
- Halogen gas handling
- Corrosion-resistant sensor
- Gas cabinets
- Condensable source routing
- Multi-gas switching on one unit
- Thin-film deposition
- Stable flow at high vapor pressure
- No cold spots in the path
- Diffusion furnaces
- Heated flow for low-volatility gases
Install Guide
- Mount on a firm, vibration-free base.
- Keep gas lines clean and dry.
- Stay below 400 kPaG (Ar: 500 kPaG).
- Warm up the unit before gas flow starts.
- Set heat to the calibration temperature first.
- Wire ±15 VDC or +24 VDC as ordered.
- Shield RS-485 cables to cut noise.
- Purge lines before process gas enters.
Setup and Care
- MGMR stores many gas and range settings in one unit.
- Swap gases without pulling the unit out.
- Heat keeps condensable gas from forming droplets.
- Stable repeatability of ±0.2% FS cuts recalibration work.
- Remote electronics option keeps heat away from control boards.
- Check fittings for leaks after warm-up.
- Hold the set temperature for best accuracy.
Compatibility Notes
- Runs on RS-485 digital networks.
- Analog control at 0–5 VDC or 4–20 mA.
- Handles common semiconductor gases, including halogens.
- Bellows valve ships as N/O or N/C.
- Works in parallel MFC layouts for warm gas delivery.
Certification Information
- CE marked for Europe.
- RoHS compliant for restricted substances.
- EP surface finish for high-purity paths.
- Metal seal leak rate at ≤1×10⁻¹¹ Pa·m³/s He.
Package Contents
- 1 × FCST1050MZF-HT heated mass flow controller
- 1 × Quick start guide
- 1 × Calibration certificate
- 1 × Safety and compliance sheet
- Fitting kit as ordered
FAQ
- Q: Why does this model have a heater?
- A: Warm walls stop condensable gases from forming liquid drops.
- Q: Can I pick my own heat setting?
- A: Yes. We offer custom calibration temperatures on request.
- Q: How do I stop droplets at startup?
- A: Let the unit reach full heat before you open the gas supply.
- Q: Which signal option fits older control racks?
- A: The +24 VDC version with 4–20 mA output is a good match.
- Q: What is a common install mistake?
- A: Running gas too early. Cold gas can block the warm path.















There are no reviews yet.