E82EV553K4B201 Lenze 8200 Vector Drive, 110 A Output

E82EV553K4B201 Lenze 8200 vector Frequency Inverter

The E82EV553K4B201 is a panel-mounted frequency inverter from the Lenze 8200 vector series. It drives a 55.0 kW four-pole asynchronous motor. This E-design unit comes without an integrated mains filter. It suits machine builders who need proven drive performance and a clear migration path.

Lenze lists the 8200 vector as a previous product. The official migration path leads to the i950 series. Lenze confirms that the i950 emulates 8200 vector behaviour via the i950 PROFIBUS module and L_ICIP library. No drop-in same-order-code replacement exists.

Technical Data

• Brand: Lenze
• Model: E82EV553K4B201
• Series: 8200 vector
• Rated motor power: 55.0 kW typical, four-pole three-phase asynchronous motor
• Output current: 110 A nominal at 1 kHz switching frequency
• Peak output current: 165 A maximum for 60 s, periodic load change cycle
• Overload capability: 1.8 x rated torque for 60 s; 2.1 x rated torque for 3 s after controller enable
• Motor control: V/f characteristic control (linear or quadratic), vector control, sensorless torque control
• Switching frequency: 1 / 2 / 4 / 8 / 16 kHz, selectable for noise or power-loss optimisation
• Max. output frequency: 0 to 650 Hz
• Supply voltage: 3/PE 320 to 550 V AC, 45 to 65 Hz; alternative DC 450 to 775 V DC supply
• Design variant: 2xx design, without integrated mains filter
• Built-in ports: control terminals X3 with digital inputs, analog input/output, and relay output K1
• Onboard fieldbus: none
• Communication expansion: plug-in I/O and fieldbus option modules, such as E82ZAFSC010 Standard I/O and E82ZAFAC010 Application I/O
• Operating temperature: -10 to +50 °C; derate by 2.5 % per °C above +40 °C
• Ambient limit at increased rated power: max. +35 °C per catalogue 11/02 p.62 footnote 4
• Storage temperature: -25 to +60 °C
• Relative humidity: average 85 % RH, without condensation, climatic class 3K3 per EN 50178
• Protection rating: IP20 per EN 60529; IP41 with push-through thermally separated mounting
• Dimensions (H x W x D): 591 x 340 x 285 mm, panel-mounted unit
• Weight: 37 kg without integrated mains filter

Installation Guide

• Mount the unit vertically on a panel. Keep clearance for airflow above and below.
• Use push-through thermally separated mounting to reach IP41 protection.
• Connect 3/PE 320 to 550 V AC supply. Check the DC 450 to 775 V DC alternative if needed.
• Wire control signals to terminals X3. Use shielded cable for analog signals.
• Fit a mains filter where local EMC rules require one. This variant has no integrated filter.
• Derate output above +40 °C ambient. Limit ambient to +35 °C when running at increased rated power.

Commissioning and Maintenance

• Set motor data from the nameplate before first run.
• Choose V/f, vector, or sensorless torque control for the load type.
• Select switching frequency to balance audible noise and power loss.
• Check fan paths and heatsink fins at each service interval.
• Verify terminal torque and cable condition during routine checks.
• Keep spare option modules on hand to reduce downtime.

Compatibility Notes

• Works with standard four-pole three-phase asynchronous motors rated 55.0 kW.
• Accepts plug-in I/O and fieldbus option modules for system integration.
• Has no onboard fieldbus or Ethernet port. Add an option module for network control.
• Migration to the Lenze i950 is supported through the i950 PROFIBUS module and L_ICIP library.
• No drop-in replacement shares the same order code.

Certifications and Compliance

• Protection rating IP20 per EN 60529; IP41 with push-through mounting.
• Climatic class 3K3 per EN 50178 for humidity and environmental endurance.
• Legacy product status confirmed on the official Lenze previous products page.
• Audit status: OFFICIAL_VERIFIED, last verified 2026-10.

Packing List and Warranty

• 1 x Lenze E82EV553K4B201 8200 vector frequency inverter
• 1 x document pack with terminal and safety information
• Warranty: 12 months
• Dispatch: 12 to 24 hours after order confirmation
• Courier: FedEx, UPS, or DHL

Expert Review

The E82EV553K4B201 remains a solid choice for plants that already run 8200 vector drives. Its 110 A nominal output and 165 A short-time peak cover heavy starts and cyclic loads. Vector control and sensorless torque control give good torque at low speed. The missing onboard fieldbus is the main limit. Budget for an option module if you need network control. Spare units are the practical route for legacy lines. Plan the i950 migration before long-term expansion.

Manager’s Insight

Buy this unit as a proven spare, not as a new platform. The 55 kW class fits pumps, fans, conveyors, and mixers. Stock one or two units for critical lines. The 12-month warranty and 12 to 24 hour dispatch reduce risk. Confirm the 2xx design has no mains filter before you install. If your site needs fieldbus control, order the matching option module at the same time.

Best Fit Equipment and Applications

• Pumps and fans with variable flow demand
• Conveyors and material handling lines
• Mixers, agitators, and process machinery
• Retrofits of existing Lenze 8200 vector installations
• Legacy machines awaiting an i950 migration plan

FAQ

Q: Does this inverter include a fieldbus port?

A: No. It has control terminals X3 only. Add a plug-in fieldbus option module for network control.

Q: Can I replace an old 8200 vector with this unit?

A: Yes, if the old unit shares the same order code and design variant. Lenze offers no drop-in replacement across generations.

Q: What is the overload capacity?

A: It delivers 1.8 x rated torque for 60 s. It also delivers 2.1 x rated torque for 3 s after controller enable.

Q: How do I handle high ambient heat?

A: Derate 2.5 % per °C above +40 °C. Keep ambient at or below +35 °C when running at increased rated power.

Q: Is a mains filter built in?

A: No. This is the 2xx design variant without an integrated mains filter. Add an external filter where EMC rules require one.

Q: What is the migration path?

A: Lenze points to the i950 series. The i950 emulates 8200 vector behaviour via the i950 PROFIBUS module and L_ICIP library.

Q: How fast do you ship?

A: Orders leave in 12 to 24 hours. We ship by FedEx, UPS, or DHL.

Q: Experienced buyer tip: what should I check first?

A: Check the motor nameplate data and the existing control wiring. Match the option module to your fieldbus before ordering.

Buying Guide

• Confirm the motor rating is 55.0 kW and four-pole.
• Check whether your line uses AC 320 to 550 V or DC 450 to 775 V supply.
• Decide if you need a fieldbus option module before you order.
• Plan for an external mains filter if EMC rules apply.
• Order a spare unit for critical lines to cut downtime.
• Ask for the i950 migration note if you plan a long-term upgrade.

Contact Information

• Inquiries: sales@powergearx.com
• Phone and WhatsApp: +86 18030005825

Copyright © 2026 Powergear X Automation Limited. All rights reserved.

Original Source: https://www.powergearx.com/