Bently Nevada 330102-00-40-10-01-00 3300 XL 8mm Proximity Probe – Vibration Monitoring Sensor

Product Overview: Premium Bently Nevada 3300 XL Vibration Monitoring Solution

This is the genuine 3300 XL 8mm Proximity Probe. It offers precise measurement for critical machinery. The probe detects shaft vibration and position. It ensures reliable protection for turbines, compressors, and motors. Trust this industry-standard tool for your predictive maintenance.

Complete Technical Specifications

• Brand & Model: Bently Nevada 330102-00-40-10-01-00
  • 330102: 3300 XL 8 mm Probe with Armor, 3/8-24 UNF Thread
  • 00: Unthreaded Length = 0 inches
  • 40: Overall Case Length = 4.0 inches
  • 10: Total Cable Length = 1.0 meter (3.3 feet)
  • 01: Miniature Coaxial ClickLoc Connector (with protector)
  • 00: Agency Approval Not Required
• Type: 3300 XL 8 mm Proximity Transducer
• Measurement Range: 2.0 mm (80 mils) linear range.
• Recommended Gap: Set at -9 Vdc (approx. 1.27 mm / 50 mils).
• Frequency Response: Dependent on cable length. Consult factory graphs for details.
• Sensitivity & Linearity: Standard 3300 XL 8mm Probe scale factor.
• Resolution: High, suitable for detecting small displacement changes.
• Temperature Range:
  • Standard: -52°C to +177°C (-62°F to +350°F).
  • Extended Tip: Up to +218°C (+425°F).
• Environmental Durability:
  • Case: AISI 303/304 Stainless Steel.
  • Tip: Robust Polyphenylene Sulfide (PPS).
  • Seal: Viton® O-ring for pressure differentials.
  • Humidity: <3% ASF change at 93% RH.
• Noise Immunity: Uses shielded coaxial cable. Supports intrinsic safety barriers.
• Electrical Data:
  • Nominal Probe Resistance (RPROBE): 7.59 Ω ± 0.50 Ω for 1.0m cable.
  • Max Cable Run: 305 meters (1000 feet) to monitor.
  • Connector: Miniature coaxial ClickLoc with protector.
• Mechanical Data:
  • Thread: 3/8-24 UNF.
  • Max Thread Engagement: 0.563 inches.
  • Unthreaded Length: 0 inches.
  • Overall Length: 4.0 inches (Case) + 1.0 meter Cable.
  • Weight: 323 g/m (11.4 oz/ft).

Quick Installation & Setup Guide

• Mounting: Install in a drilled and tapped 3/8-24 UNF hole.
• Thread Engagement: Do not exceed 0.563 inches.
• Gap Setting: Adjust probe to achieve -9.0 ± 0.2 Vdc for radial vibration.
• Wiring: Use 16-24 AWG shielded cable. Ensure proper grounding.
• Sealing: The Viton® O-ring provides the seal. It is not pressure-tested by default.

Easy Calibration and Maintenance

• Calibration is straightforward using a micrometer and gap-voltage chart.
• The robust PPS tip and SST case resist corrosion and wear.
• Routine checks involve verifying gap voltage and cable integrity.

System Compatibility

• Directly compatible with Bently Nevada 3300 XL Proximitor sensors.
• Works with most monitoring systems accepting -1 to -17 Vdc gap signals.
• Can interface with PLCs and DCS via appropriate transmitters.

Certifications & Safety Approvals

• Intrinsically Safe (ia): AEx/Ex ia IIC T5…T1 Ga for Zone 0.
• Non-Incendive (nA, ec): AEx/Ex nA/ec IIC T5…T1 Gc for Zone 2/Div 2.
• Approved for Class I, II, III, Div 1 & 2, Groups A-G.

Package Contents & Support

• One (1) Bently Nevada 3300 XL 8mm Probe.
• Miniature ClickLoc connector protector attached.
• 12-Month Warranty against material and workmanship defects.
• Shipping: We ship globally via FedEx, UPS, and DHL.

Typical Applications & Diagnostic Power

• Applications: Steam/Gas Turbines, Centrifugal Compressors, Pumps, Fans, Motors, Gearboxes.
• Diagnostics: Measures radial shaft vibration, detects misalignment, unbalance, bearing wear, and rotor rub. Key for predictive maintenance programs.

Frequently Asked Questions

General & Technical

• What is the purpose of this probe?

It measures shaft vibration and position to protect rotating machinery.

• What is the best gap voltage to use?

Set it to -9 Vdc for most radial vibration measurements.

Experience-Based

• The reading seems noisy. What should I check?

First, inspect the cable shield and connectors for damage. Ensure the run is away from power cables.

• Can I use this probe in a high-temperature environment?

Yes, the extended range tip handles up to 218°C. Ensure the cable rating is also suitable.

Selection Guide

• How do I choose the right probe length?

Add your case length, thread engagement, and required clearance to the target.

• Do I need a pressure-sealed probe?

If your casing has internal pressure, contact us. Standard probes have seals but are not tested.

Need help choosing? Contact our experts for advice. Email sales@powergearx.com or message on WhatsApp: +86 18030005825.

Our Partner: Oiltech Controls Limited

Our Partner: PLCDCS HUB Limited

Copyright © 2025 Powergear X Automation Limited. All rights reserved.

Original Source: https://www.powergearx.com/