Product details
Product Overview
ATV320U22N4W is a Schneider Electric Altivar Machine drive. It delivers 2.2 kW for three-phase motors. The unit comes in an IP66 wall-mount enclosure. A category C2 EMC filter is built in. You can mount it close to the motor and save cabinet space.
This model suits conveyors, packaging machines, and simple handling axes. It runs asynchronous motors and synchronous PM motors. Setup is fast through the built-in CANopen and Modbus Serial line port. One slot accepts fieldbus modules for plant-wide control.
Key Technical Data
- Brand: Schneider Electric
- Model: ATV320U22N4W
- Series: Altivar Machine ATV320
- Module type: Three-phase variable speed drive, wall-mount
- Motor power: 2.2 kW (3 HP) at 380 to 500 V
- Supply voltage: 380 to 500 V three-phase, -15%/+10%, 50/60 Hz
- Output frequency range: 0.1 to 599 Hz
- Switching frequency: 2 to 16 kHz, factory set 4 kHz
- Nominal output current: 5.5 A at 4 kHz
- Transient output current: 8.3 A for 60 s (150% overload)
- Overload torque: up to 200% Tn over-torque, 170% Tn braking torque
- Maximum input current: 8.7 A at 380 V, 6.6 A at 500 V
- Apparent power: 5.7 kVA at 500 V
- SCCR: 5 kA maximum
- Resolution: analog output 10 bits
- Control modes: U/F ratio, sensorless flux vector, PM motor vector control
- Braking: internal braking transistor, external resistor 54 Ω minimum
- Power dissipation: 74 W at In
I/O and Signal Performance
- Analog inputs: 3 inputs. One bipolar differential ±10 V, one 0 to 10 V, one 0 to 20 mA
- Digital inputs: 6 inputs. Four configurable 24 V DC sink/source, one PTC probe, one pulse input up to 20 kHz
- Digital output: 1 configurable 24 V DC sink/source, 100 mA maximum
- Analog output: 1 output, 0 to 10 V or 0/4 to 20 mA, 10-bit resolution
- Relay outputs: 2 outputs. One NO/NC contact plus one NO contact, 3 A at 250 VAC
- Pulse output: 1 output up to 32 kHz, 24 V, 0.1 A
- Safety inputs: 1 STO input plus 4 configurable safety inputs
- Linear response: stable speed control across the full 0.1 to 599 Hz band
- Noise immunity: integrated C2 EMC filter limits conducted emissions
Environment and Durability
- Operating temperature: -10 to +50 °C without derating, up to 60 °C with derating
- Storage temperature: -25 to +70 °C
- Relative humidity: 5 to 95%, no condensation
- Protection rating: IP66
- Altitude: no derating to 1000 m. Above 1000 m, derate 1% per 100 m up to 3000 m
- Shielded motor cable: 10 m maximum at 4 kHz for C2 and C3
- Ambient class: IEC 60721-3-3 class 3C3/3S2
- Mounting: vertical ±10°, 100 mm free space around the drive
Installation Guide
- Mount the drive upright on a solid wall. Keep 100 mm clearance on all sides.
- Use Frame 3 wire sizes from 2.5 to 6 mm². Tighten terminals to 1.4 N·m.
- Connect the motor cable shield to ground at both ends. Keep cable length within 10 m.
- Add an external braking resistor if the load needs fast stops. Use 54 Ω minimum.
- Wire the STO input to the safety circuit before you power the drive.
Setup and Maintenance
- Use the graphic display terminal VW3A1111 or VW3A1101 for fast parameter access.
- Run the auto-tuning step after you enter motor nameplate data.
- Set the switching frequency above 4 kHz only with power derating.
- Check fan airflow and terminal torque at each service interval.
- The IP66 enclosure allows washdown cleaning in food and beverage areas.
Compatibility Notes
- Built-in ports: 1 RJ45 port for CANopen and Modbus Serial line
- Expansion slot: Modbus TCP/EtherNet/IP, PROFIBUS DP V1, DeviceNet, EtherCAT, POWERLINK, PROFINET
- Motors: asynchronous motors and synchronous PM motors
- Accessories: display terminals, UL Type 1 kits, DIN rail plates, GV2 breaker bracket, 90-degree control adapter, braking resistors
- Cybersecurity: no published Achilles certification. Plan network segmentation.
Certifications
- UL 508C and UL 61800-5-1
- CSA 22.2 N274
- EN/IEC 61800-3 category C2/C3
- EN/IEC 61800-5-1
- IEC 61800-5-2 up to SIL3
- IEC 61508 SIL3 and IEC 13849-1 PLe
- RCM, EAC, KC
Packing List
- 1 x ATV320U22N4W drive
- 1 x installation manual NVE41289
- 1 x safety information sheet
- Terminal labels and cable clamps
- Display terminal and fieldbus modules ship separately
FAQ
Q: Can this drive run a 3 HP motor on a 400 V line?
A: Yes. The 2.2 kW rating matches a 3 HP motor at 380 to 500 V. Check the motor nameplate current against the 5.5 A output.
Q: Does the IP66 rating allow outdoor use?
A: The enclosure resists dust and water jets. Add a sun shield and keep the ambient below 50 °C for outdoor installs.
Q: How do I connect the drive to a PLC?
A: Use the RJ45 port for Modbus or CANopen. For PROFINET or EtherNet/IP, fit the matching module in the expansion slot.
Q: What is the shortest stopping time I can reach?
A: A 54 Ω external resistor gives strong braking. Actual stop time depends on load inertia and duty cycle.
Q: From experience, what causes tripping at start-up?
A: Most trips come from a long motor cable or a missing ground bond. Keep the shielded cable under 10 m and check the PE connection.
Q: Do I need to derate above 4 kHz switching frequency?
A: Yes. The drive loses output current as frequency rises. Apply the catalog derating curve and confirm the motor current.
Q: Can I mount the drive on a DIN rail?
A: Use the optional DIN rail mounting plate. The drive is heavy at 7.7 kg, so add a mechanical stop.
Q: Which display should I order?
A: The VW3A1111 graphic terminal gives full menus and copy functions. The VW3A1101 is a lower-cost remote option.
















There are no reviews yet.