330193-00-03-10-00 Bently Nevada 3300 XL 8mm Probe – Fast Ship Reliable Shaft

Product Overview

• 330193-00-03-10-00 – Bently Nevada 3300 XL 8 mm Probe
• Type: M10 x 1 thread, without armor
• Made in U.S.A
• Non-contact eddy current sensor for shaft vibration & position

Key Technical Data

• ▶ Configuration & Dimensions
  • Unthreaded Length: 0 mm (minimum) / 230 mm (maximum)
  • Overall Case Length: 30 mm
  • Total Probe Length: 1.0 meter (3.3 feet)
  • Thread: M10 x 1, max engagement 15 mm
• ▶ Electrical & Resistance
  • Nominal DC Resistance (RPROBE): 7.59 Ω ± 0.50 Ω
  • High linearity for precise gap measurement
• ▶ Materials & Construction
  • Tip: Polyphenylene sulfide (PPS)
  • Case: AISI 303 or 304 stainless steel
  • Seal: Viton® O-ring for differential pressure
• ▶ Temperature Range
  • Standard Probe: -52°C to +177°C (-62°F to +350°F)
  • Extended Tip: up to +218°C (+425°F)
  • Cable & Connector: -51°C to +260°C (-60°F to +500°F)
  • Caution: below –34°C (–30°F) may damage pressure seal
• ▶ Humidity & Immunity
  • Humidity: < 3% scale factor change after 56 days at 93% RH (IEC 68-2-3)
  • 60 Hz magnetic field immunity: minimal output voltage (as low as 0.0004 mV pp/Gauss)

Installation & Maintenance

• ✔ Mount using M10x1 threaded hole, hand tighten plus 1/4 turn
• ✔ Set initial gap between 0.5 mm and 1.5 mm for best linear range
• ✔ Clean tip gently with isopropyl alcohol if needed
• ✔ Inspect cable and connector for wear during routine checks
• ✔ Not pressure tested before shipping – contact support if pressure test required

Applications & Compatible Equipment

• ✅ Steam turbines, gas turbines, centrifugal compressors
• ✅ Pumps, fans, motors, and hydro generators
• ✅ Axial position monitoring and radial vibration measurement
• ✅ Works with Bently Nevada 3300 XL monitors and 3500 system
• ✅ Pairs with 3300 XL Proximitor® sensors

Comparison with Extension Cables

• For longer reach or armored protection, consider these extension cables:
  • 330190-045-02-00 – Standard armored extension cable
  • 330190-045-02-05 – Armored with hazardous area approvals
• Selection tip: Use armored cables in high-vibration or abrasive environments. This unarmored probe is lighter and suits clean panel routing.
• Related product: 3300 5mm Proximity Probes for smaller target surfaces.

Expert Review & Manager’s Insight

• Manager’s Insight: “This probe delivers trusted Bently Nevada precision. The 1.0 meter length fits tight junction box placements. With no agency approval needed, it’s cost‑effective for non-hazardous plants. Stocked for 24‑hour dispatch – keep one as a critical spare.”
• Expert Review: “Field data shows excellent stability over wide temperature swings. The Viton seal holds up in wet environments. Easy to install and compatible with standard Proximitor systems. A solid choice for predictive maintenance programs.”

Professional FAQ

• Q: What is the advantage of 1.0 meter total length?
  A: It reduces cable clutter and minimizes signal loss. Perfect for machines where the driver is close to the probe.
• Q: Can I use this probe with armored extension cables?
  A: Yes. Combine with 330190 series armored cables for extra mechanical protection. Ensure total system length matches driver calibration.
• Q: Does this model require hazardous area certification?
  A: No. The “00” approval means it is for general purpose (non‑hazardous) locations. Use approved versions for Zone 0 or Zone 2 areas.
• Q: How should I store the probe if not used immediately?
  A: Store in original packaging between -52°C and +177°C. Avoid mechanical stress on cable. Inspect O‑ring before installation after long storage.
• Q: What is the typical lifespan?
  A: With correct installation, over 10 years in continuous service. Bently Nevada probes are known for long‑term reliability.

Selection & Purchasing Guide

• ✔ Confirm total length (1.0 m) fits your machine layout.
• ✔ Check thread compatibility – M10x1 is standard for many compressor casings.
• ✔ No hazardous area approval needed, ideal for general industrial sites.
• ✔ Warranty: 12 months against manufacturing defects.
• ✔ Shipping: 12-24 hours dispatch from stock. Express via FedEx, UPS, DHL.

Packaging & Support

• 📦 Box includes: 1 probe, calibration record, installation sheet.
• 📞 Contact us: sales@powergearx.com | +86 18030005825 (WhatsApp)
• ✅ Technical support available – we answer within 2 business hours.

Copyright © 2026 Powergear X Automation Limited. All rights reserved.
Original Source: https://www.powergearx.com/