FPNO-21 ABB PROFINET Adapter – FPNO-21 Fieldbus Module for Drives, Fast Ship

Portfolio de Produtos

• FPNO-21 is a PROFINET IO adapter module from FIG.
• It plugs into an option slot on an ABB drive control unit.
• It links the drive to a PROFINET IO network.
• Install is quick. No special tools needed.
• The module finds the network speed by itself.
• It works at 10 Mbit/s or 100 Mbit/s.

O que você pode fazer com isso

• Send control commands to the drive, such as Start, Stop, and Run enable.
• Feed a speed or torque reference to the drive.
• Send a process value or reference to the drive PID controller.
• Read drive status and actual values.
• Recupere uma falha na unidade de acionamento.
• Read and write drive parameters.
• Connect the Drive composer pro tool.
• Sync the real time clock.

dados técnicos

• marca: FIG
• Modelo: FPNO-21
• Tipo: PROFINET fieldbus adapter module
• Protocolo: PROFINET IO
• Taxa de transferência: 10 Mbps or 100 Mbps, auto-detect
• Serial Type: Meio duplex ou full duplex
• Conexões: Três
• Poder: +3.3 V ±5%, max 400 mA, from the drive
• Protecção: IP20
• Conselho de Administração: Revestido Conformal
• EMC: Meets EN 61800-3:2004
• Indicadores: Três LEDs bicolores

Layout do conector

• Conector de pino 20 para a entrada
  • Carries power and drive data
• X1 RJ-45 para Ethernet
  • Main network port
• X2 RJ-45 for chaining
  • Links another adapter module

Detalhes da conexão Ethernet

• Works with IEEE 802.3 and IEEE 802.3u devices
• 10BASE-TX or 100Base-TX
• Auto-negotiation and Auto-MDIX on board
• Cabo: CAT5e/6 S/FTP, S/STP, or SF/FTP
• Segmento máximo: 100 m / 328 ft
• Topologia: Bus, star, or ring
• Ring limit: Nós 50
• Chain limit: 50 nodes recommended
• Each unit adds 19 μs forward delay
• 50 nodes add about 1 ms delay

Guia de LED

• LED HOST
  • Flashing green: linking to drive
  • Green: drive link OK
  • Flashing red: drive link lost for a moment
  • Flashing orange with MODULE orange: file system error. Cycle power. Call ABB if it stays.
• MÓDULO LED
  • Off: no power
  • Flashing orange: blink mode for ID
  • Flashing green: waiting for PROFINET link
  • Green: normal run
  • Flashing red twice per second: link is down. Check cables.
  • Flashing red once per second: data does not fit the message type. Check group B and C settings.
  • Red: port disabled or duplicate address. Check IP or cycle power.
  • Flashing red-green: self test
  • Flashing orange with HOST orange: file system error. Cycle power. Call ABB if it stays.
• REDE/LED DE REDE
  • Off: not on-line, or address check not done, or no power
  • Flashing green: sending or receiving data

Environment and Packing

• Drive manual ambient rules apply.
• Pack: cardboard box.
• Wrap: antistatic air bubble sheet (PE).

Guia de instalação

• Power off the drive first.
• Slide the module into the option slot.
• Seat the 20-pin connector firmly.
• Plug the network cable into X1.
• Use X2 to chain the next unit.
• Set the station name in your PLC tool.
• Power up and check the LEDs.

Configuração e manutenção

• Os LEDs mostram o status rapidamente.
• Auto-detect cuts setup steps.
• O Auto-MDIX elimina as dúvidas sobre a fiação.
• The coated board resists dust and damp.
• Keep the slot cover closed when not in use.

Compatibilidade

• Compatível com inversores ABB que possuam um slot opcional livre.
• Works with standard PROFINET IO masters.
• Works with Drive composer pro.
• Uses standard RJ-45 Ethernet cables.

Equipamentos e casos de uso mais adequados

• ABB drives in factory automation lines.
• Conveyor and pump drive networks.
• Fan and mixer control cabinets.
• Estações de tratamento de água e esgoto.
• Food and packing machines.
• Any plant that runs PROFINET IO.

Análise especializada

• The FPNO-21 is a small part with a big job.
• It turns a stand-alone drive into a network node.
• Two RJ-45 ports allow daisy chains.
• That saves switch ports and cable runs.
• Ring mode adds a path for fault tolerance.
• The LED codes are clear and fast to read.
• Setup is simple for trained staff.
• It suits both new builds and upgrades.

Visão do gerente

• Keep one spare module per site.
• Label station names on each drive.
• Plan ring size before you add nodes.
• Long chains need a longer cycle time.
• Train techs on the LED codes.
• Fast swaps cut downtime a lot.

Garantia e Envio

• Garantia 12-month neste módulo.
• Os pedidos são enviados em 12 para 24 horas.
• Entregue por FedEx, UPS, ou DHL.
• O número de rastreamento será enviado após o despacho.

Perguntas frequentes

• Q: Does the module set its own network speed?
  • A: Yes. It auto-detects 10 or 100 Mbit/s.
• Q: Can I link several drives in one line?
  • A: Yes. Use X2 to chain units. Keep it to 50 nodes or fewer.
• Q: What does a red MODULE LED mean?
  • A: The port is off, or two devices share one address. Check the IP, then cycle power.
• Q: How do I pick the right cable?
  • A: Use CAT5e/6 shielded cable with RJ-45 plugs. Keep runs under 100 m.
• Q: Is a spare unit worth the cost?
  • A: Yes. A spare module can restart a line in minutes.

Contato

• Email: vendas@powergearx.com
• WhatsApp: + 86 18030005825
• Need help with a part number? Ask us. We reply fast.

Direitos de Autor

• Copyright © 2026 Powergear X Automation Limited. Todos os direitos reservados.
• Fonte Original: https://www.powergearx.com/