Name: Lenze E82ZZ22234B210 EMC Filter for E82EV222K4C200 2.2 kW Drive
SKU: E82ZZ22234B210
Price: 214.00 USD
Availability: InStock

Product details

E82ZZ22234B210 Lenze 8200 vector RFI Filter – LD Long-Motor-Cable Design

E82ZZ22234B210 is a passive RFI (EMC) filter from the Lenze 8200 vector series. It uses the LD long-motor-cable design. This filter suppresses electromagnetic interference on the E82EV222K4C200 frequency inverter (2.2 kW, 3~ 400/500 V). It meets limiting value classes A and B. The unit is a legacy accessory. Lenze lists it in the official 8200 vector accessories catalogue.

This filter is a direct-fit mains accessory. It needs no setup and no communication interface. Installers pair it with the matched inverter and route long motor cables with lower noise risk. The LD design supports long motor cable runs. That makes it a practical choice for retrofits and spare-part planning on existing 8200 vector drives.

Why This Filter Matters

Matched pairing: Built for the E82EV222K4C200 inverter at 2.2 kW.
EMC control: Limits conducted interference on mains and motor lines.
Long cable support: The LD variant targets long motor-cable installations.
Passive design: No firmware, no settings, no communication link.
Simple service: Swap-in replacement for legacy 8200 vector systems.

Technical Data

Brand: Lenze
Model: E82ZZ22234B210
Series: 8200 vector
Module type: Passive RFI / EMC filter
Design: LD, long-motor-cable variant
Matched inverter: E82EV222K4C200, 2.2 kW, 3 AC 400/500 V
Supply voltage: 3 AC 400/500 V, mains side
Rated current: 4.5 A nominal
Filter classes: Limiting value classes A and B
Dimensions (H x W x D): 337 x 60 x 40 mm
Weight: 0.9 kg
Measurement range: Not published by the manufacturer
Frequency response: Not published by the manufacturer
Sensitivity: Not applicable to a passive filter
Linearity: Not published by the manufacturer
Resolution: Not applicable to a passive filter
Temperature range: Not published; follows host inverter conditions
Environmental tolerance: Not published; passive mains accessory
Noise immunity: Passive suppression of conducted emissions
Humidity: No specific %RH value published
Protection rating: Not published by the manufacturer
Storage temperature: Not published by the manufacturer

Installation Guide

Mount the filter close to the E82EV222K4C200 inverter.
Keep mains and motor cables short and well separated.
Bond the filter housing to the panel earth.
Use shielded motor cable for long runs.
Check cable length against the LD design limits.
Power off the drive before you start wiring.
Follow Lenze 8200 vector mounting instructions.

Setup and Maintenance

No commissioning steps are needed for this passive unit.
No software, address, or parameter setup applies.
Inspect terminals and earth bonds at routine service.
Replace the filter if you find damage or loose parts.
Keep the unit clean and free of metal dust.
Log filter changes in your drive service records.

Compatibility Notes

Matched to the E82EV222K4C200 inverter only.
Part of the Lenze 8200 vector accessory family.
Fits 3 AC 400/500 V mains supplies.
No fieldbus or communication interface is present.
Lenze names no official successor filter for this part.
Confirm fitment before you buy for other drive models.

Approvals and Compliance

Designed for limiting value classes A and B.
Supports EMC compliance of the host drive system.
Final EMC results depend on the full panel build.
No separate certificate data is published for this filter.
Verify local EMC rules for your installation.

Packing List and Warranty

Expert Review

The E82ZZ22234B210 is a focused spare part. Its value sits in one job: clean EMC behavior on long motor cables for the 2.2 kW 8200 vector drive. The LD design saves engineering time on retrofits. Keep expectations realistic. This is a legacy accessory, so stock and documentation are limited. Buyers should confirm the exact inverter code before ordering. For maintenance teams that still run 8200 vector drives, this filter is a sound, low-risk spare.

Manager’s Insight

Demand for this part comes from service and repair work, not new designs. Hold small stock for key accounts. Check inverter nameplates during order review. Pair each sale with a note on cable shielding. That advice cuts repeat EMC complaints. Price it as a service part, not a commodity. Fast shipping wins here, because downtime drives the purchase. Reach our team at sales@powergearx.com or +86 18030005825 for fitment checks.

Best-Fit Equipment and Applications

Lenze 8200 vector drives in existing machines
E82EV222K4C200 inverters at 2.2 kW
Panels with long motor cable runs
Retrofit and spare-part programs
Conveyors, pumps, fans, and simple handling axes
Plants that need class A or B EMC limits

FAQ

Which inverter does this filter fit?
It matches the E82EV222K4C200 drive at 2.2 kW. Check your nameplate first.
Does it need any setup?
No. It is passive. There is nothing to configure.
What does LD mean?
LD is the long-motor-cable design. It targets long cable runs.
Is a successor part available?
Lenze names no official replacement. Source the same code when you can.
Can I use it on another drive brand?
No. Fit and EMC results are tied to the matched Lenze drive.
How fast do you ship?
Orders leave in 12 to 24 hours by FedEx, UPS, or DHL.
What is the warranty?
12 months from delivery.
Experienced buyer tip: what should I check first?
Look at cable length and shield bonding. Most EMC faults start there.
Buying advice: when should I replace the filter?
Replace it after physical damage, loose terminals, or a failed EMC test.
Buying advice: how many should I keep in stock?
Keep one spare per active 8200 vector drive on site.
How do I confirm fitment?
Send your drive nameplate photo to sales@powergearx.com.