IS220PVIBH1A GE Mark VIe Vibration Monitor I/O Pack IS220PVIBH1A Fast Shipping

IS220PVIBH1A GE Mark VIe Vibration Monitor I/O Pack

• IS220PVIBH1A is a GE Mark VIe vibration monitor I/O pack.
• It links one or two I/O Ethernet networks to a vibration terminal board.
• It reads proximity, vibration and Keyphasor signals.
• Thirteen channels handle many sensor types.
• It supports TMR and simplex backup protection.
• This pack is new and original.
• It ships in 12 to 24 hours.
• It carries a 12 month warranty.

Model Decode: IS220PVIBH1A

• IS220
  • Mark VIe modular assembly.
  • Domestic original manufacture.
• PVIB
  • Vibration monitor function code.
• H1
  • Product grouping and revision.
• A
  • Single A rated functional revision.

Compatible Accessories

• IS220PVIBH1A
  • Terminal board IS200TVBAH2A.
  • Three negative power supply daughterboards IS200WNPSH1A.
• IS420PVIBH1B
  • Terminal board IS200TVBAH2A.
  • Three negative power supply daughterboards IS200WNPSH1A, IS400WNPSH1A or IS40yTVBAH2B.
• IS220YVIBS1A
  • Terminal board IS200TVBAS2A.
  • Three negative power supply daughterboards IS200WNPSS1A.
• IS42yYVIBS1B (y = 0 or 1)
  • Terminal board ISx0yTVBAS2A (x = 2 or 4, y = 0 or 1).
  • Three negative power supply daughterboards ISx0yWNPSS1A or IS40yTVBAS2B.

Key Specifications

• Brand: General Electric
• Model: IS220PVIBH1A
• Series: Mark VIe
• Type: Vibration Monitor I/O Pack
• Channels: 13 for proximity and vibration
• Dimensions: 3.25 in high x 1.65 in wide x 4.78 in deep
• Weight: 1 lb
• Ambient Temperature: -30 to 65 °C (-22 to 149 °F)
• Common Mode Voltage: Min 5 VDC
• Frame Rates: 3.125, 6.25, 12.5, 25, 50 and 100 Hz
• Probe Power: -24 VDC, 12 mA load per transducer
• LED Indicators: 4, labeled Attn, Pwr, Link, TxRx
• Board Compatibility: Vibration Terminal Board (TVBA)
• Revisions: Rev. A, Rev. B, Rev. C, Rev. D

Electrical Ratings

• Power Supply Voltage
  • PVIBH1B and YVIBS1B: min 27.4 V dc, nominal 28.0 V dc, max 28.6 V dc.
  • PVIBH1A and YVIBS1A: min 27.4 V dc, nominal 28.0 V dc, max 28.6 V dc.
• Power Supply Current
  • Max 0.98 A dc.
• Vibration Inputs
  • Voltage min -20 V dc, max 15.6 V dc.
• Position Inputs
  • Voltage min -20 V dc, max -0.5 V dc.
• Buffered Outputs
  • Voltage min -20 V dc, max 4.5 V dc.
  • Current min -3 mA dc.
• Probe Power
  • Voltage min -25.2 V dc, nominal -24 V dc, max -22.8 V dc.
  • Current max 12 mA dc.

Channel Layout

• Channels 1 to 3
  • Accelerometers with integrated output.
• Channels 1 to 8
  • Proximitors, Velomitors and Seismic sensors.
• Channels 9 to 12
  • Proximitors only.
• Channel 13
  • Proximity or Keyphasor signal.

Installation Guide

• Secure the terminal board first.
• Plug the pack into the board connector.
• Use the threaded studs near the Ethernet ports to secure the pack.
• Connect one or two Ethernet wires.
• Use ENET1 for the R controller network when using dual links.
• Plug the power connector in at the side.
• Check that the N28 power supply daughterboard sits well in the TVBA connector.
• Set up the pack in ToolboxST.

Operation Highlights

• The processor runs self-tests before loading code from flash.
• Auto reconfiguration lets you swap packs without manual setup.
• A new pack downloads its file from the controller at boot.
• The BAFA acquisition board and KAPA daughterboard shape signals.
• Signal centering and gain boost analog-to-digital resolution.
• Two independent 10/100 Ethernet ports keep data flowing.
• One network failure will not stop the pack.
• A watchdog timer and reset circuit add safety.
• The pack reads trip board status through feedback signals.

Manager’s Insight

• This pack is a strong pick for legacy Mark VIe sites.
• It keeps older turbine control systems running.
• Auto reconfiguration cuts downtime during swaps.
• Dual Ethernet links add network resilience.
• Stock this pack for fast replacement needs.

Best Fit Equipment and Applications

• Gas and steam turbine control systems.
• Mark VIe distributed I/O cabinets.
• Plants using Bently Nevada proximity probes.
• Velomitor and seismic sensor loops.
• Keyphasor speed and phase monitoring.
• TMR and simplex backup protection setups.

FAQ

• Can I swap this pack without reprogramming?
• Yes. Auto reconfiguration loads the file from the controller.
• Which sensors fit channels 1 to 3?
• Accelerometers with integrated output fit these channels.
• What does channel 13 accept?
• It takes a proximity or Keyphasor signal.
• How many Ethernet ports does it have?
• It has two independent 10/100 Ethernet ports.
• What if one network fails?
• The pack keeps running and flags the fault on the LED.
• Which tool sets up the pack?
• Use ToolboxST for configuration.
• What is the lead time?
• Orders ship in 12 to 24 hours.
• Which couriers do you use?
• We use FedEx, UPS and DHL.
• What warranty comes with it?
• Each unit has a 12 month warranty.
• How do I pick the right revision?
• Match the pack to your terminal board and power board first.
• Can I get help before buying?
• Yes. Email sales@powergearx.com or call +86 18030005825.

Buying Guide

• Check your terminal board number first.
• Confirm the power daughterboard type.
• Match the frame rate to your network needs.
• Review sensor types per channel.
• Plan for TMR or simplex mode.
• Keep one spare pack on site.
• Ask about stock before you order.
• Contact sales@powergearx.com or +86 18030005825 for advice.

Copyright © 2026 Powergear X Automation Limited. All rights reserved.

Original Source: https://www.powergearx.com/