Product details
Product Description
- ABB 3HAC026253-001 is a genuine I/O power supply board for IRC5 and OmniCore controllers.
- It belongs to the DSQC661 product family.
- The board delivers a regulated 24 V DC output to I/O modules.
- Internal circuits monitor voltage and current conditions.
- This module keeps I/O communication stable in robot cells.
- ABB Robotics lists it as a genuine spare part.
- Use it to replace a failed or aging board in your controller cabinet.
Technical Data
- Brand: ABB
- Model: 3HAC026253-001
- Series: ABB Robotics IRC5 / OmniCore Spare Parts
- Product type: DSQC661
- Function: I/O power supply
- Output: 24 V DC stabilized output to I/O bus
- Communication: Internal voltage and current monitoring
- Supply voltage: Not published by ABB. Distributor listings conflict: 100–240 V AC vs 24 V DC / 12–36 V DC.
- Output current: Distributor values conflict: 2 A vs 20 A vs 1.25 A. No official value adopted.
- Operating temperature: 0 to +45 °C (family-level IRC5 controller ambient)
- Storage temperature: -25 to +55 °C (family-level IRC5 controller ambient)
- Relative humidity: 5% to 95%, non-condensing
- Protection rating: IP20 (internal cabinet module)
- Dimensions (H×W×D): Not published by ABB. Distributor listings conflict: 104×178×235 mm vs 60×38×20 mm vs 52.5×32×140 mm.
- Weight: Not published by ABB. Distributor listings conflict: 2.46 kg vs 0.02 kg vs 0.15 kg.
- Lifecycle status: ABB Robotics genuine spare part (last verified: 2026-11)
Key Performance Parameters
- Measurement range: Internal voltage and current monitoring for the I/O bus.
- Frequency response: Not published by ABB for this board.
- Sensitivity: Not published by ABB for this board.
- Linearity: Not published by ABB for this board.
- Resolution: Not published by ABB for this board.
- Temperature range: 0 to +45 °C operating, -25 to +55 °C storage.
- Environmental tolerance: 5% to 95% RH non-condensing, IP20 cabinet protection.
- Interference immunity: Not published by ABB for this board.
Installation Guide
- Power off the IRC5 or OmniCore controller before work.
- Open the controller cabinet and locate the I/O power supply slot.
- Remove the old board carefully. Keep mounting screws.
- Insert the DSQC661 board into the correct slot.
- Tighten all screws to secure the board.
- Reconnect all cables to the board.
- Close the cabinet and restore power.
- Check the 24 V DC I/O bus supply after startup.
Commissioning and Maintenance
- Commissioning is simple: power on and confirm 24 V DC output.
- Watch the controller event log for I/O power faults.
- Inspect the board and connectors during regular service.
- Keep the cabinet interior clean and within temperature limits.
- Replace the board if voltage monitoring reports a fault.
Compatibility Notes
- Fits ABB IRC5 controllers that use the DSQC661 board.
- Also fits OmniCore controllers that accept this spare part.
- Feeds 24 V DC to I/O modules on the I/O bus.
- Verify your controller model and slot before ordering.
- Contact ABB support if your controller label shows a different part number.
Certification Information
- ABB publishes no board-level certification list for this part.
- The controller cabinet carries the main system certifications.
- Ask ABB for a current certificate if your project requires one.
Package Contents
- 1× ABB 3HAC026253-001 I/O power supply board (DSQC661)
- Mounting screws as supplied by ABB
- No extra cables or manuals unless stated by the seller
FAQ
- Q: What does this board do?
- A: It supplies regulated 24 V DC to I/O modules in the controller.
- Q: Which controllers use it?
- A: IRC5 and OmniCore controllers that accept the DSQC661 spare part.
- Q: What is the input voltage?
- A: ABB does not publish it. Distributor values conflict, so check with ABB.
- Q: What output current can it deliver?
- A: No official figure exists. Distributor listings disagree, so confirm with ABB.
- Q: Is it a genuine ABB part?
- A: Yes. ABB Robotics lists it as a genuine spare part.
- Q: Why do dimensions and weight differ between sellers?
- A: Distributor data conflicts. ABB has no public board-level dimension or weight table.
- Q: How do I confirm the board works after fitting?
- A: Power on the controller and check the event log for I/O power faults.
- Q: Can I install it myself?
- A: Yes, if you follow ABB service procedures and power off the cabinet first.
- Q: What if my controller shows a different part number?
- A: Contact ABB support to confirm the correct replacement before ordering.
- Q: How is the board protected inside the cabinet?
- A: The board sits inside the cabinet, which provides IP20 protection.














There are no reviews yet.