ລາຍລະອຽດຜະລິດຕະພັນ
ລາຍລະອຽດຂອງຜະລິດຕະພັນ
ໄດ້ MDA90A-0120-503-X-S00 is a single-axis inverter from SEW-EURODRIVE. ມັນເປັນຂອງ ໂມດູນ MOVIDRIVE® platform and runs one motor from a shared DC link. Rated output is 12 A. ໄດ້ S00 ປະສົມປະສານການເພີ່ມຄຳຕໍ່ທ້າຍ Safe Torque Off (STO) per EN 61800-5-2. Electrical data matches the base model MDA90A-0120-503-X-000. A typical asynchronous motor load is 5.5 kW. SEW DriveConfigurator still lists full product data.
ລາຍລະອຽດລະຫັດສັ່ງຊື້
- MDA90A-0120-503-X-S00 - ລະຫັດສັ່ງຊື້ເຕັມຮູບແບບ
- MDA90A — ອິນເວີເຕີ MOVIDRIVE® ໂມດູນແກນດຽວ, ໃຊ້ພະລັງງານຈາກ DC-link
- 0120 - 12 A ກະແສໄຟຟ້າຜົນຜະລິດທີ່ໄດ້ຮັບການຈັດອັນດັບ (ຊັ້ນປະສິດທິພາບ)
- 503 — ລະຫັດຕົວແປອຸປະກອນ; ພາລາມິເຕີໄຟຟ້າພື້ນຖານນຳໃຊ້
- X — ລະຫັດການຕັ້ງຄ່າມາດຕະຖານຂອງໂຮງງານ
- S00 - ປະສົມປະສານ STO ຕົວແປຄວາມປອດໄພ (000 = ບໍ່ມີຄວາມປອດໄພປະສົມປະສານ)
- X — ລະຫັດການຕັ້ງຄ່າມາດຕະຖານຂອງໂຮງງານ
- 503 — ລະຫັດຕົວແປອຸປະກອນ; ພາລາມິເຕີໄຟຟ້າພື້ນຖານນຳໃຊ້
- 0120 - 12 A ກະແສໄຟຟ້າຜົນຜະລິດທີ່ໄດ້ຮັບການຈັດອັນດັບ (ຊັ້ນປະສິດທິພາບ)
ຂໍ້ມູນຈໍາເພາະດ້ານວິຊາການ
- Identity
- ຍີ່ຫໍ້: SEW-EURODRIVE
- Model: MDA90A-0120-503-X-S00
- ຊຸດ: ໂມດູນແກນດຽວແບບໂມດູນ MOVIDRIVE®
- ປະເພດ: ໂມດູນອິນເວີເຕີແກນດຽວ (ໃຊ້ພະລັງງານຈາກການເຊື່ອມຕໍ່ DC)
- ຂໍ້ມູນໄຟຟ້າ
- ແຮງດັນໄຟຟ້າເຊື່ອມຕໍ່ DC: 750–800 V DC (ສາຍ 380–400 V → 750 V; 480–500 V → 800 V)
- ອັດຕາຜົນຜະລິດໃນປະຈຸບັນ: 12 A
- ເກີນ ກຳ ລັງ: 250% ຂອງກະແສໄຟຟ້າທີ່ກຳນົດໄວ້ສູງສຸດ 1 ວິນາທີ
- ຄວາມຖີ່ຂອງຜົນຜະລິດ: U/f 599 Hz · VFCplus 250 Hz · CFC 500 Hz · ELSM 500 Hz (ສູງສຸດ)
- ແຫຼ່ງຈ່າຍໄຟເສີມ: DC 24 V (-10 % / +20 %)
- Standby power: 4.3 W; energy-saving standby cuts use up to 89%
- ພະລັງງານມໍເຕີໂດຍປົກກະຕິ: 5.5 kW ແບບບໍ່ປະສານກັນ (ASM)
- ຄວາມປອດໄພ
- STO ປະສົມປະສານຕໍ່ EN 61800-5-2 (ຮຸ່ນ S00)
- ການສື່ສານ ແລະ ທາງເລືອກຕ່າງໆ
- ລົດເມລະບົບຜ່ານ backplane (X30): EtherCAT / SBusPLUS
- ບັດທາງເລືອກ: /CES11A (ຫຼາຍຕົວເຂົ້າລະຫັດ), /CID21A (ຕົວເຂົ້າລະຫັດ), /CIO21A (I/O), /CS..A (ຄວາມປອດໄພ), /L (ການເຄືອບແບບ conformal)
- Terminals
- Motor U/V/W (sizes 1–2 terminals; sizes 3–5 X2 copper bars)
- 24 V aux: X5; ຈຸດສູງສຸດຂອງການສະໜອງ encoder 1000 mA: X15
- ກ່ຽວກັບສິງແວດລ້ອມ
- ເວລາປະຕິບັດການ: 0 ເຖິງ +45 ° C (ບໍ່ມີການຫຼຸດລະດັບ)
- ອຸນຫະພູມການເກັບຮັກສາ: -25 ຫາ +70 °C (ບໍ່ກັ່ນຕົວ)
- ການປົກປ້ອງ: IP20 — ຕ້ອງຕິດຕັ້ງຕູ້
- ກົນ
- ຄວາມກວ້າງຂອງແຜ່ນພື້ນຖານ 60 ມມ; ຄວາມເລິກ 355 ມມ (ຂະໜາດເຕັມຕໍ່ຮູບແຕ້ມຂະໜາດ)
- Lifecycle
- ແພລດຟອມໂມດູນ MOVIDRIVE® ລຸ້ນເກົ່າ; ຜູ້ສືບທອດແມ່ນ MOVI-C® (ຂໍ້ມູນຖືກຢັ້ງຢືນ 2026-09)
ຜົນປະໂຫຍດທີ່ສໍາຄັນໃນທັນທີ
- One compact axis module drives a full 5.5 kW motor with 250 % peak current for hard starts.
- Built-in STO removes the external safety contactor and cuts wiring time.
- A shared DC link lets multiple axes exchange braking energy and saves cabinet space.
- Plug-in option cards add encoders, I/O, safety and fieldbus as the machine evolves.
- Energy-saving standby slashes idle power by up to 89%.
ຄູ່ມືການຕິດຕັ້ງ
- ຕິດຕັ້ງແນວຕັ້ງໃສ່ແຜງ ຫຼື ພື້ນຫຼັງພາຍໃນຕູ້ຄວບຄຸມ IP20.
- Leave clear top and bottom air gaps; do not exceed 45 °C ambient without derating.
- Feed the DC link from an MDP90A or MDR90B supply module.
- Connect motor cables to U/V/W and 24 V aux to X5.
- Wire the encoder to X15 and the system bus through the backplane (X30).
- Route motor cables separately from signal cables to reduce interference.
- Connect STO signals to a safety controller before enabling the axis.
- Tighten terminals to the torque shown in the dimension drawing.
ການມອບໝາຍ ແລະ ບຳລຸງຮັກສາ
- Set up and tune with SEW DriveConfigurator or MOVITOOLS® Studio.
- Run motor auto-tuning; save the parameter set for cloning to spare units.
- Front diagnostic LEDs show state and fault codes at a glance.
- Modular design lets you swap one axis without removing neighboring modules.
- Option cards plug in from the front; no rewire of power circuits.
- Check firmware in the tool; update only with SEW-approved files.
ເຂົ້າກັນໄດ້
- ຈັບຄູ່ກັບໂມດູນສະໜອງແບບໂມດູນ MOVIDRIVE® MDP90A ແລະ MDR90B.
- Shares one DC link bus with other MDA90A axis modules in the same cabinet.
- ຍອມຮັບບັດຕົວເລືອກ /CES11A, /CID21A, /CIO21A, /CS..A ແລະ /L.
- Speaks EtherCAT and SBusPLUS over the backplane system bus.
- Not drop-in compatible with MOVI-C®; use MOVI-C® for new designs.
ໃບຢັ້ງຢືນການ
- ໜ້າທີ່ຄວາມປອດໄພຂອງ STO ໄດ້ຮັບການຮັບຮອງ EN 61800-5-2 (ຮຸ່ນ S00).
- ເຄື່ອງໝາຍ CE ສຳລັບຕະຫຼາດເອີຣົບ; ຂໍໃບຢັ້ງຢືນ UL/cUL ຫຼື ໃບຢັ້ງຢືນທາງທະເລຈາກແຜ່ນຂໍ້ມູນ.
- PCB ເຄືອບດ້ວຍ Conformal ມີຕົວເລືອກ /L ສຳລັບສະພາບແວດລ້ອມທີ່ຮຸນແຮງ.
ເນື້ອຫາການຫຸ້ມຫໍ່
- ໂມດູນອິນເວີເຕີແກນດຽວ 1 × MDA90A-0120-503-X-S00
- ສະກູຕິດຕັ້ງທີ່ສະໜອງໃຫ້ໂດຍ SEW-EURODRIVE
- ຄູ່ມືເລີ່ມຕົ້ນດ່ວນ ແລະ ບັນທຶກຄວາມປອດໄພ (ດິຈິຕອນຜ່ານລະຫັດ QR)
- ພາລາມິເຕີເລີ່ມຕົ້ນຈາກໂຮງງານໂຫຼດໃສ່ໜ່ວຍກ່ອນການຂົນສົ່ງ
ຄໍາຖາມທີ່ຖືກຖາມເລື້ອຍໆ
- Q: Does the S00 version still need an external safety relay?
- A: No. Safe Torque Off is built in. Wire the safety controller directly to the STO inputs.
- Q: Can I swap a 000 unit for this S00 module?
- A: Yes. Electrical ratings stay identical; only the integrated safety function differs. Map STO in your circuit.
- Q: Which supply module feeds this axis?
- A: Use an MDP90A or MDR90B supply module to create the shared DC link.
- Q: What motor size fits a 12 A output?
- A: A 5.5 kW asynchronous motor is typical. Confirm with the MOVIDRIVE motor assignment table.
- Q: How long can it deliver 250 % current?
- A: Up to one second, then it returns to the 12 A rated level.
- Q: Can I add fieldbus or encoders later?
- A: Yes. Plug in /CES11A, /CID21A, /CIO21A or /CS..A cards as needed.
- Q: [Field experience] The unit faults immediately on power-up — where do I start?
- A: Check 24 V aux at X5 and DC-link voltage. The STO inputs must close before the drive enables.
- Q: [Field experience] Should I keep this as a spare?
- A: The platform is legacy. Stock critical spares on site; specify MOVI-C® for new machines.
- Q: [Field experience] Why does the motor overheat in summer?
- A: Cabinet air above 45 °C forces derating. Add cooling or size up the drive.
- MDA90A — ອິນເວີເຕີ MOVIDRIVE® ໂມດູນແກນດຽວ, ໃຊ້ພະລັງງານຈາກ DC-link


















ມີຄວາມຄິດເຫັນທີ່ບໍ່ມີ.